ARRIS C250 V2 FPV Racing Drone RTF with Aomway Commander V1 FPV Goggle Boundle

ARRIS C250 V2 FPV Racing Drone RTF with Aomway Commander V1 FPV Goggle Boundle

  • Model: CA0144
  • Shipping Weight: 4kg
  • Units in Stock: 12
  • Manufactured by: ARRIS

Price:   $659.00

Please Choose:

  • Mode2(left hand throttle)
  • Mode1(right hand throttle)

Order this & earn 330 reward points

  • Details
  • Reviews
  • FAQ

ARRIS C250 V2 250mm fpv racing quads rtf with Aomway Commander V1 boundle comes with everything you needed for FPV. The ARRIS C250 V2 is fully assembled and tested before leaving the factory, and the radio is upgraded to AT9S.With the goggle, you can begin your FPV journey.


Main Features:

1. Simple structure frame installed with tower structure ESC/PDB, easy to assemble and easy to repair.
2. High quality 3K Carbon fiber frame, the material is imported from Janpan
3. 4mm thick arms, super strong and durable
4. Super Light frame, only $136g
5. The tower ESC/FC comes with integrated OSD, no need to install it separately
6. The angle of the FPV camera is adjustable
7. 4mm thick arms, super strong and durable
8. High efficiency X2205 2300KV motor provides you better performance and longer working life
9. High quality 5042 3 blade propeller, 10% higher efficiency than normal propellers
10. High safety 4S 1500mah 50C lipo battery




Dimension:195mm x 230mm x 42mm (Propellers not included)
Diagonal Wheelbase: 250mm
Flight Controller: F3 flight Controller
Frame Material: Pure Carbon fiber
BNF weight:350g
Radio System: Radiolink AT9S with R6DSM receiver
Camera: ARRIS XAT700M FPV Mini Camera
FPV TX: 5.8G 200mw 40CH
Antenna: 5.8G Antenna
Flying Time: 10min hovering
Battery: ARRIS 4S 1500mah 50C Lipo
Charger: Skyrc Imax B6AC V2 Charger
Goggle: Aomway commander V1 FPV Goggle with dual receiver and DVR


ARRIS C250 V2 is made of pure carbon fiber material. With water transfer painting technology,it look so charming. The upper plate and side plate adopts 1.5mm pure carbon fiber material, decrease the weight of the whole frame. Meanwhile, the motor arm adopts 4mm carbon fiber material, ensure the strength of the frame. The total weight of the frame is about 137g.With the simplify one-piece design and lower gravity center design, all kinds of flight actions can be done with facility.The layout design of the C250 V2 is reasonable, the standard flight controller and PDB board can install there.On the frame, there is reserved space for the XT60 female battery connector.The motor arm has holes for 220x series motors, and both 5 inches and 6 inches propellers can install on the C250 V2 frame.

The main advantages of the 4in1 30A Tower:

1. With the double layer design, you just need to plug the pins between esc and flight controller, flight controller and other electronic components. The layout is more concise, decrease the weight of the drone, provided guarantee for flight performance improvements.
The power for flight controller and camera is provided by the BEC on the flight controller. The power for video transmitter is provided by battery. This improves the anti-interference of the video transmission.


2. The tower integrated the OSD, avoid to install it additionally and the adjustment.The drone could get a quick response to the throttle during the flight.


3. The Tower structure design protects the ESC well during the flight. According to our experience, some of the ESC were damaged by the propeller rotation or tree brunch cut, and some of the ESC were damaged due to the broken of the motor arm during the crash when it installed on top of the motor arm. Sometimes, in order to protect the ESC, we added ESC cover to protect it. From this, the weight of the drone increased. For this tower, the esc integrated in the tower which installed in the middle of the quad frame, the ESCs can be protected quite well and make it looks better.



With the high performance ARRIS X2205 2300KV brushless motor, the ARRIS C250 V2 has outstanding power.
Main Features:

1. Adopts the brand new M5 steel shaft, improving the structure strength.
2. Anti-slip pro design.
3. Upgrade to centrifugal fan design, optimizing the heat dissipation.
4. Adopts original Japan NSK bearing, improving the performance of the motor.
5. Adopts N52 tile-shaped magnets.
6. The motor passed more than 20 kinds of tests before leaving the factory, ensure the quality of the motor.



The ARRIS C250 V2 adopts with the latest 5042 propeller, it has bigger windward area, well balance and strengthen root, and the efficiency is 10% higher than normal propeller. This propeller is the first choice of FPV racing drones.



ARRIS XAT700M FPV Mini Camera for FPV Racing Drones--ARRIS XAT700M HS1177 fpv mini camera is specially designed for FPV. This camera performs well in both bright and dark condition with 700TVL high quality image. And the camera angle on the drone is adjustable.



ARRIS 5.8g 200mW 40-CH video TX and antenna pre-assembled.The ARRIS TS5823L with LED is transmitting a full range of 40 channels and only weighs 10g. It's perfect for a wide range of aircraft!With a goggle or monitor in hand, you can begin your FPV journey.



ARRIS X-Speed C250 V2 has integrated with a remote controller battery warning buzzer, pilot can set the threshold (adjustable) according to CF parameter-adjustment software. In addition, you can also locate your racing drone through triggering the buzzer with the switch D on the transmitter.



Self-level mode is the easiest to fly, because when you leave the stick at the center and not controlling it, your drone just level itself and stays there.This mode is good for beginners.

Manual mode is useful for acrobatics such as flips or rolls, or FPV when smooth and fast control is desired. The picture below is what we set on our own Radiolink AT9S Radio.



RadioLink AT9S 9-Channel 9CH 2.4GHz Transmitter + R9D Receiver.The AT9S radio is with high performance-price ratio. And it can support strength, receiver voltage monitored, extending battery voltage, temperature, motor RPM, GPS etc.

High safety ARRIS 4S 1500mah Lipo Battery

ARRIS 4S 1500mAh 50C lipo battery is specially designed for FPV racer. The price of this battery is much higher than the similar batteries in the market, because we only sell top-quality batteries. As we all know, the low quality battery might have potential safety hazard, we will never tolerate such products.For ARRIS 4S 1500mah lipo battery, we have done UN38.3 test,1.2M Drop test,MDS report for it, for the test report, you can check here.





Aomway Commander V1 FPV goggles comes with 16:9 and 4:3 switchable display radio with 32°FOV.With the HDMI port, it supports 720P and 3D signal inputs.Commander V1 goggle also comes with 5.8G 40CH built-in diversity high-sensitivity diversity module,DVR function and head tracker (optional).It supports the diopter lens, -2, -4 and -6 dpt.are optional.The goggle also comes with high-speed ventilating fan installed to prevent fogging up on screens.


Main Features:

1. 16:9 and 4:3 ratio switchable (FOV: 32°)
2. Supports 3D,720P
3. Built-in 2 5.8G high sensitivity RF module
4. High-speed ventilating fan installed
5. Support head tracker (module optional)
6. Built-in DVR


FOV: 32°
Ratio: 16:9,4:3
Lens: Glass optics (binocular)
Resolution: 854x480 WVGA LCD display, LED backlight

3D function:Side/Side 3D
Interpupillary Distance:Adjustable 59-69mm
Audio Output:Stereo
Video Format:NTSC / PAL auto switch
HD Input:Support 720p,C-type HDMI port
Operation:Brightness / contrast / channel selection / display mode /DVR / head tracker
Auto Scan:One key starts auto search the channel of strongest signal
Head Tracker: 2-axis head tracker (only for advanced version)

DVR Recording:
1. Only for RF and AV in mode
2. TF card support up to 32GB
3. video compression format: MJPG 30fps

Built-in 40CH Diversity Receiver:
1. Dual 40CH high-sensitivity diversity RF module,
2. Auto switch to strong signal antenna
3. Channel display on screen

1. DC in: standard 5.5*2.1 (inner positive outer negative)
2. AV in: 3.5mm four-pole AV jack port
3. Audio: 3.5mm three-pole earphone jack port
4. Head tracker: PS2 data port
5. TF card slot for recording

Working Voltage Range:DC 7-18V (2S-4S), OSD display voltage status
Working Environment:- 0°C to 55°C
Unit Weight: 172g
Package Size: 230*165*77mm

SKYRC IMAX B6AC V2 Professional Balance Charger/Discharger

SKYRC IMAX B6AC V2 is the upgraded version for well-known IMAX B6AC. Compared with B6AC V2, it is more accurate and stable and also has some new features and functions. Users could set the terminal voltage by themselves and connect it to PC for PC control and firmware upgrade. What's more, users could also use it as Lithium Battery Meter and Battery Internal Resistance Meter. There are Automatic Charging Current Limit, Capacity Limit, Temperature Threshold and Processing Time Limit which makes the charger safer than V1.
SKYRC B6AC V2 is a high-performance, micro processor control charge/discharge station with battery management suitable for use with all current battery types, with integral equalizer for six-cell Lithium- Polymer (LiPo), Lithium iron phosphate(LiFe) and Lithium-Ion (LiIon) batteries; maximum 6A charge current and maximum 50W charge power.



AC Input Voltage: 100-240V
DC Input Voltage: 11-18V
Circuit Power: Max Charge: 50W /Max Dischage: 5W
Charge Current Range: 0.1-6.0A
Discharge Current Range: 0.1-2.0A
LiPo/LiFe/LiIon Cells: 1-6S
NiMH/NiCd Cells:1-15S
Pb(Lead Acid) battery Voltage:2-20V
Net Weight: 632g
Dimension: 135 x 144 x 36mm


Package Include:

1 x ARRIS C250 V2 Racing Quad Frame
4 x ARRIS X2205 2300KV Brushless Motors
1 x Flycolor Tower w/ F390 30A 4 in 1 ESC + F3 + OSD + PDB
4 x ARRIS 5042 3-blade Propeller
1 x ARRIS XAT700M FPV Mini Camera
1 x 5.8G 200mw 32CH FPV TX
1 x FPV Transmitter Antenna
1 x Radiolink AT9S Transmitter with receiver
1 x ARRIS Buzzer
1 x ARRIS 4S 1500mah Lipo Battery
1 x SKYRC IMAX B6AC V2 Balance Charger
1 x Aomway Commander V1 FPV Goggle


Note: Due to the battery in the parcel, the shipping time may take longer than usual!

Similar Products
Who's Online
There currently are 15 guests online.